Harnesses for 2.0 Wifi boxes

Harnesses for 2.0 Wifi boxes

From: 0,00 €

  • Click on the image to choose this model

    Plugs into J7 (12 pin) socket in the case.
    Equipped with 4 connectors at its end, it connects the harnesses:

    • - No. 4 (Intermediate harness for the HPS 1 high pressure rail probe)
    • - No. 6 (Intermediate harness for the IAT 1 air intake temperature sensor)
    • - No. 8 (Intermediate harness for the second air intake temperature sensor IAT 2)
    • - No. 19 (Intermediate harness for the second high pressure rail probe HPS 2)
    Click on the image to choose this model

    Intermediate harness for modification of the information from the high pressure probe located on the injection rail (HPS 1)

    Connects to:

    • - One of the 4 connectors of harness 3 (J7).
    • - Harness 5: Final harness which connects to the high pressure probe of the injection rail (HPS 1)

    HPS = High Pressure Sensor

    Click on the image to choose this model

    Final harness for modification of the information from the high pressure probe located on the injection rail (HPS 1).

    This small harness plugs into: 

    • - Beam 4: HPS 1 intermediate beam
    • - High pressure probe of the injection rail
    • - The connector which is originally connected to the high pressure probe of the HPS 1 injection rail

    HPS = High Pressure Sensor

    *Choosing the type of connectors
    Click on the image to choose this model

    Intermediate harness for modification of the air intake temperature sensor information (IAT 1)

    Connects to:

    • - One of the 4 connectors of harness 3 (J7).
    • - Harness 7: Final harness that connects to the air intake temperature sensor (IAT 1)

    IAT = Intake Air Temperature

    Click on the image to choose this model

    Final harness for modification of the intake temperature sensor information (IAT 1).

    This small harness plugs into: 

    • - Beam 6: intermediate beam IAT 1
    • - Air intake temperature sensor, it can be located on the flow meter (MAF sensor) or it is a sensor located before or after the throttle body.
    • - The connector that is originally connected to the IAT 1 air intake temperature sensor

    IAT = Intake Air temperature

    *Choosing the type of connectors
    Click on the image to choose this model

    Intermediate harness for modification of the information from the air intake temperature sensor in the intake manifold (IAT 2)

    Connects to:

    • - One of the 4 connectors of harness 3 (J7).
    • - Harness 9: Final harness that connects to the air intake temperature sensor (IAT 2)

    IAT = Intake Air Temperature

    Click on the image to choose this model

    Final harness for modification of the intake temperature sensor information (IAT 2).

    This small harness plugs into: 

    • - Beam 8: IAT 2 intermediate beam
    • - Air intake temperature sensor, it can be located on the flow meter (MAF sensor) or it is a sensor located before or after the throttle body.
    • - The connector that is originally connected to the IAT 2 air intake temperature sensor

    IAT = Intake Air temperature

    *Choosing the type of connectors
    Click on the image to choose this model

    Ethanol sensor wiring harness

    Connects to:

    • - On the connector of harness 17 (J1) provided for this connection.
    • - Ethanol sensor
    Click on the image to choose this model

    Harness with double fuse for powering the heating strip relay

    Connects to:

    • - On the 12V relay connector provided for this connection.
    • - In the fuse box on a 12V ACC fuse location (12V after ignition)

    Zoom on the 4 different types of fuses

    *We offer 4 models of double fuses to choose from, please check the type of fuse you are going to connect to before making your choice
    Click on the image to choose this model

    Y-shaped harness to connect 2 heating strips when the engine is a V6 or V8

    Connects to:

    • - Beam 13: Intermediate beam with 12V relay.
    • - Heating strips x2
    Click on the image to choose this model

    Intermediate harness with 12V relay which connects the heating strip(s), the 2.0 box, and the 12V ACC power supply

    Connects to:

    • - Beam 17: Beam J1 which connects several beams.
    • - Heating strip x1 or Beam 12 if connecting 2 heating strips
    • - Double fuse wire 11: 12V ACC power supply
    Click on the image to choose this model

    Harness with temperature sensor, to be fixed on the heating hose or on the thermostat outlet.

    Connects to:

    • - Harness 17: Harness J1 which plugs into the housing and connects harnesses 15, 14, 13, 10
    Click on the image to choose this model

    Intermediate harness for +12V ACC power supply of the 2.0 box, necessary if your box must operate in one of the following 2 cases:
    - Operation of the box on a direct injection engine.
    - If the ramp heater option is installed and active, this will supply 12V ACC to the 2.0 box without interruption when you turn on the vehicle ignition, so you can trigger and manage the operation of the heating strips.

    Connects to:

    • - Harness 17: Harness J1 which plugs into the housing and connects harnesses 15, 14, 13, 10
    • - Harness 16: double fuse that plugs into the fuse box to supply the 2.0 box with +12V ACC
    Click on the image to choose this model

    Wiring harness with double fuse for powering the 2.0 box in +12V ACC (+12V after contact), necessary if your box must operate in one of the following 2 cases:
    - Operation of the box on a direct injection engine.
    - If the ramp heater option is installed and active, this will supply 12V ACC to the 2.0 box without interruption when you turn on the vehicle ignition, so you can trigger and manage the operation of the heating strips.

    Connects to:

    • - Harness 15: Intermediate harness for +12V ACC power supply from the box
    • - In the fuse box on a fuse location +12V ACC (+12V after ignition)

    Zoom on the 4 different types of fuses

    *We offer 4 models of double fuses to choose from, please check the type of fuse you are going to connect to before making your choice
    Click on the image to choose this model

    Plugs into J1 (9 pin) socket in the case.
    Equipped with 4 connectors at its end, it connects the harnesses:

    • - No. 15: Intermediate harness for 12V ACC power supply (only if direct injection or rail heater option activated and installed)
    • - No. 14: Temperature sensor harness to be fixed on the engine
    • - No. 13: Intermediate harness with 12V relay to connect the heating strip(s)
    • - No. 10: Ethanol sensor harness
    Click on the image to choose this model

    Final harness for modification of the information from the high pressure probe located on the injection rail (HPS 2).

    This small harness plugs into: 

    • - Beam 19: HPS 2 intermediate beam
    • - High pressure probe of the injection rail
    • - The connector which is originally connected to the high pressure probe of the HPS 2 injection rail

    HPS = High Pressure Sensor

    *Choosing the type of connectors
    Click on the image to choose this model

    Intermediate harness for modification of the information of the high pressure probe located on the injection rail (HPS 2)

    Connects to:

    • - One of the 4 connectors of harness 3 (J7).
    • - Harness 18: Final harness which connects to the high pressure probe of the HPS 2 injection rail

    HPS = High Pressure Sensor

SKU: beams-2-0 Category:

Description

Harnesses for connecting the new 2.0 Wifi box (except injector harnesses).

Here are all the harnesses that make up the connections on the 2.0 Wifi box.
Choose your bundles according to the options you already have or want.

2 year warranty

Free delivery in mainland France / Sending by post via Colissimo