Harnesses for 2.0 Wifi boxes

From: 0,00 €

  • Beam 3
    Click on the image to choose this model

    Plugs into J7 (12 pin) socket in housing.
    Equipped with 4 connectors at its end, it connects the harnesses:

    • - No. 4 (Intermediate harness for the HPS 1 high pressure rail probe)
    • - No. 6 (Intermediate harness for the IAT 1 air intake temperature sensor)
    • - No. 8 (Intermediate harness for the second IAT 2 air intake temperature sensor)
    • - No. 19 (Intermediate harness for the second HPS 2 high pressure rail probe)
    Beam 4
    Click on the image to choose this model

    Intermediate harness for modifying the information of the high pressure probe located on the injection rail (HPS 1)

    Connects to:

    • - One of the 4 connectors of harness 3 (J7).
    • - Harness 5: Final harness which connects to the high pressure probe of the injection rail (HPS 1)

    HPS = High Pressure Sensor

    Beam 5
    Click on the image to choose this model

    Final harness for modifying the information of the high pressure probe located on the injection rail (HPS 1).

    This small harness connects to: 

    • - Beam 4: HPS intermediate beam 1
    • - High pressure probe of the injection rail
    • - The connector which is originally connected to the high pressure probe of the HPS 1 injection rail

    HPS = High Pressure Sensor

    *Choice of connector type
    Beam 6
    Click on the image to choose this model

    Intermediate harness for modifying information from the air intake temperature sensor (IAT 1)

    Connects to:

    • - One of the 4 connectors of harness 3 (J7).
    • - Harness 7: Final harness which connects to the air intake temperature sensor (IAT 1)

    IAT = Intake Air Temperature

    Beam 7
    Click on the image to choose this model

    Final harness for modifying the information of the intake temperature sensor (IAT 1).

    This small harness connects to: 

    • - Beam 6: IAT 1 intermediate beam
    • - Air intake temperature probe, it can be located on the flow meter (MAF probe) or it is a probe which is located before or after the throttle body.
    • - The original connector connected to the IAT 1 air intake temperature sensor

    IAT = Intake Air temperature

    *Choice of connector type
    Beam 8
    Click on the image to choose this model

    Intermediate harness for modifying the information of the air intake temperature sensor in the intake manifold (IAT 2)

    Connects to:

    • - One of the 4 connectors of harness 3 (J7).
    • - Harness 9: Final harness which connects to the air intake temperature sensor (IAT 2)

    IAT = Intake Air Temperature

    Beam 9
    Click on the image to choose this model

    Final harness for modifying the information of the intake temperature sensor (IAT 2).

    This small harness connects to: 

    • - Beam 8: IAT 2 intermediate beam
    • - Air intake temperature probe, it can be located on the flow meter (MAF probe) or it is a probe which is located before or after the throttle body.
    • - The original connector connected to the IAT 2 air intake temperature sensor

    IAT = Intake Air temperature

    *Choice of connector type
    Beam 10
    Click on the image to choose this model

    Ethanol sensor connection harness

    Connects to:

    • - On the connector of harness 17 (J1) provided for this connection.
    • - Ethanol sensor
    Beam 11
    Click on the image to choose this model

    Harness with double fuse for powering the heating strip relay

    Connects to:

    • - On the 12V relay connector provided for this connection.
    • - In the fuse box on a 12V ACC fuse location (12V after contact)

    Zoom on the 4 different types of fuses

    *We offer 4 models of double fuses to choose from, please check the type of fuse you are going to connect to before making your choice
    Beam 12
    Click on the image to choose this model

    Y-shaped harness to connect 2 heater strips when the engine is a V6 or V8

    Connects to:

    • - Harness 13: Intermediate harness with 12V relay.
    • - Heating strips x2
    Beam 13
    Click on the image to choose this model

    Intermediate harness with 12v relay which connects the heating strip(s), the 2.0 box, and the 12V ACC power supply

    Connects to:

    • - Beam 17: Beam J1 which connects several beams.
    • - Heating strip x1 or Bundle 12 if connecting 2 heating strips
    • - Double fuse wire 11: 12V ACC power supply
    Beam 14
    Click on the image to choose this model

    Harness with temperature sensor, to be attached to the heating hose or to the calorstat output.

    Connects to:

    • - Harness 17: Harness J1 which plugs into the box and which connects harnesses 15, 14, 13, 10
    Beam 15
    Click on the image to choose this model

    Intermediate harness for powering up +12V ACC of the 2.0 box, necessary if your box must operate in one of the following 2 cases:
    - Operation of the box on a direct injection engine.
    - If the rail heater option is installed and active, this will supply 12V ACC to the 2.0 box without interruption when you turn on the vehicle's ignition, so you can trigger and manage the operation of the heating strips.

    Connects to:

    • - Harness 17: Harness J1 which plugs into the box and which connects harnesses 15, 14, 13, 10
    • - Harness 16: double fuse which plugs into the fuse box to supply the 2.0 box with +12V ACC
    Beam 16
    Click on the image to choose this model

    Harness with double fuse for supplying the 2.0 box with +12V ACC (+12V after contact), necessary if your box must operate in one of the following 2 cases:
    - Operation of the box on a direct injection engine.
    - If the rail heater option is installed and active, this will supply 12V ACC to the 2.0 box without interruption when you turn on the vehicle's ignition, so you can trigger and manage the operation of the heating strips.

    Connects to:

    • - Harness 15: Intermediate +12V ACC power harness from the case
    • - In the fuse box on a +12V ACC fuse location (+12V after contact)

    Zoom on the 4 different types of fuses

    *We offer 4 models of double fuses to choose from, please check the type of fuse you are going to connect to before making your choice
    Beam 17
    Click on the image to choose this model

    Plugs into socket J1 (9 pin) in housing.
    Equipped with 4 connectors at its end, it connects the harnesses:

    • - No. 15: Intermediate harness for 12V ACC power supply (only if direct injection or rail heater option activated and installed)
    • - No. 14: Temperature sensor harness to attach to the engine
    • - No. 13: Intermediate harness with 12V relay to connect the heating strip(s)
    • - No. 10: Ethanol sensor harness
    Beam 18
    Click on the image to choose this model

    Final harness for modifying the information of the high pressure probe located on the injection rail (HPS 2).

    This small harness connects to: 

    • - Beam 19: HPS 2 intermediate beam
    • - High pressure probe of the injection rail
    • - The connector which is originally connected to the high pressure probe of the HPS 2 injection rail

    HPS = High Pressure Sensor

    *Choice of connector type
    Beam 19
    Click on the image to choose this model

    Intermediate harness for modifying the information of the high pressure probe located on the injection rail (HPS 2)

    Connects to:

    • - One of the 4 connectors of harness 3 (J7).
    • - Harness 18: Final harness which connects to the high pressure probe of the HPS 2 injection rail

    HPS = High Pressure Sensor

SKU: beams-2-0 Category:

Description

Harnesses allowing you to connect the new 2.0 Wifi box (except injector harnesses).

Here are all the harnesses that make up the connections on the 2.0 Wifi box.
Choose your bundles according to the options you already have or want.

2 years warranty

Free delivery in mainland France / Sending by post via Colissimo